Corsaro 1200 Veloce - after flashing ECU won't start

Erfahrungen, Tipps und mehr zur 1200er Corsaro

Moderator: gk

fandaism
Colomi
Colomi
Beiträge: 6
Registriert: Dienstag 9. August 2022, 11:02

Corsaro 1200 Veloce - after flashing ECU won't start

Beitrag von fandaism »

Hello guys,

currently I am trying to flash my ECU for an (EbisUltimativeRace05 - 23ACMOR95C) map. I have it downloaded from here: https://ecu-repo.spiro-media.de/Ducati- ... es/Morini/
My original map - 3219MOCO39F is ridable, strong middle and top, but at lower speed, it is so bad from 2 to 4,5K RPM bike is struggling a lot.
Bike is made in 2K18 ad is on original setup. Termignoni silencers with DB killers and catalyst.

My problem is that when I write an EBI's map, bike won't start (every electronic is fine, everything works like normal, but when I press start button, nothings happen).

Then I wrote back an original map and it starts again.
So i am very confused where the problem could be.

Here are reports from Guzzidiag soft. There are no errors and map was load correctly.

I will be grateful for any help

Bild
Bild
Bild
Dateianhänge
2022-08-09_12-53-32.jpg
2022-08-09_12-53-32.jpg (65.46 KiB) 2137 mal betrachtet
298494318_6127715493911620_8605242710001509686_n.jpg
298494318_6127715493911620_8605242710001509686_n.jpg (54.11 KiB) 2137 mal betrachtet
298610882_6127715453911624_6023085457944737318_n.jpg
298610882_6127715453911624_6023085457944737318_n.jpg (138.8 KiB) 2137 mal betrachtet
fandaism
Colomi
Colomi
Beiträge: 6
Registriert: Dienstag 9. August 2022, 11:02

Re: Corsaro 1200 Veloce - after flashing ECU won't start

Beitrag von fandaism »

So I have tried to upload all the maps, which I could download and the result is same for all of them.
Bike does not start. I believe that it is some small thing in the code that prevents the motor from starting.

Would be anybody capable here to check mine original map vs another ones? There must be some difference inside which is causing this.
corsaro1200
Morinisti
Morinisti
Beiträge: 666
Registriert: Mittwoch 14. Januar 2009, 20:10
Wohnort: Oberbayern
Kontaktdaten:

Re: Corsaro 1200 Veloce - after flashing ECU won't start

Beitrag von corsaro1200 »

fandaism hat geschrieben: Dienstag 9. August 2022, 12:57 Hello guys,

My original map - 3219MOCO39F
Bike is made in 2K18 ad is on original setup. Termignoni silencers with DB killers and catalyst.
your original map isn't known for me (see this at first time) :sternchen:
I think, new models from 2018 like Veloce, ZZ or ZT have a new Configuration in cause of EURO4 and a second Lambda. An "old" map, as Ebi06 or all of them at the Server, are not compatible to your "new" System. This should be a reason for your engine, not to start.
Maybe - i'm not sure :nichtverstehn:
Hope you can find an easy way to fix this.

Regards
Dieter
Habe niemals zu hohe Erwartungen, dann kannst du nicht enttäuscht werden.
fandaism
Colomi
Colomi
Beiträge: 6
Registriert: Dienstag 9. August 2022, 11:02

Re: Corsaro 1200 Veloce - after flashing ECU won't start

Beitrag von fandaism »

Ahh that is an interesting reminder.

It is true that mine is running with 2 lambdas which means its EURO4. Maybe If I unplug the second one on a cat, it could work? I was also thinking if there could be some ECU protection agains flashing, like Immobilizer.

Maybe it's just time to write to the factory or some dealer support to give some ideas.
I have tried to compare these two maps in a tunepro and it found 8256 bytes of difference :D, which means that EBI's map is totaly different.

But anyway thank you :)
fandaism
Colomi
Colomi
Beiträge: 6
Registriert: Dienstag 9. August 2022, 11:02

Re: Corsaro 1200 Veloce - after flashing ECU won't start

Beitrag von fandaism »

So after some digging I have found that since I have 2 lambda sensors before cat I can't use all the other older maps, because it can't work. These two lambdas are like a control element for the injectors, so if you shut them injectors and ECU don't have any input. There is a reason why my bike won't start.

Only option is to modify current map on a dyno or by some licence tuning product. Only other option could be to find somebody who has also this new bike and who has been through all this before.

Thats all :-)
corsaro1200
Morinisti
Morinisti
Beiträge: 666
Registriert: Mittwoch 14. Januar 2009, 20:10
Wohnort: Oberbayern
Kontaktdaten:

Re: Corsaro 1200 Veloce - after flashing ECU won't start

Beitrag von corsaro1200 »

fandaism hat geschrieben: Donnerstag 11. August 2022, 16:24 to find somebody who has also this new bike and who has been through all this before.
thanks for your Information.
There are only a few people with a "new" (2 Lambda) Bike, our specialists here have all an "old" Version. I guess, there will be no "modified" SW be available :cry:
Have Fun :)
Habe niemals zu hohe Erwartungen, dann kannst du nicht enttäuscht werden.
brmoke
Morinisti
Morinisti
Beiträge: 243
Registriert: Montag 24. Dezember 2012, 17:18
Wohnort: 75233 Tiefenbronn

Re: Corsaro 1200 Veloce - after flashing ECU won't start

Beitrag von brmoke »

Habe mir von Michal sein Mapping schicken lassen, es deckt sich mit meinem Basismapping, das ich aus Italien für meine auf 2 Lambdasonden umgebaute Granpasso bekommen hatte. Die einzigen Unterschiede sind die Softwarebezeichung und die Tachokalibrierung. Die Anlasseransteuerung wandert softwaregesteuert auf einen anderen Pin. Die Pinbelegung der ECU entspricht derjenigen der Stelvio 1200 8V.
Ich habe ein passendes XDF erstellt und das Mapping auf die anderen Einspritzdüsen IWP189 in Verbindung mit dem kleinen Motor optimiert; bin im Verbrauch um 1 ltr/100 km runtergekommen.

Schöne Grüße, Benedikt

P.S. die TPS-Werte nach Reset liegen bei 5° bei mir bzw. 5,3 ° bei Michal, obwohl bei mir die 1,9° der Granpasso und bei Michal 2,33 ° eingetragen sind. Da scheint im Code noch etwas draufgerechnet zu werden; bin mit Meinolf im Austausch.
Die kürzeste Verbindung zwischen zwei Punkten ist eine Gerade, die schönste eine Kurve !
Antworten

Zurück zu „Corsaro 1200“